Proof Portal
Omarchy
ProbeLabs65 findings · 95 requirementsA proof layer — requirements, tests and verified fixes — for two of Omarchy's subsystems: the application menu (launcher scripts, QML model, JSONC config, search and selection) and the lock screen (lock scripts, QML, PAM authentication). Scope is deliberately limited to those components of omacom/omarchy; the rest of the distribution is not covered.
Network speed test reports 0 Mbps when Wi-Fi and Ethernet are both active
Reported by Ry0dai · filed Aug 25, 2026 · open at source
At a glance
- 1 · What is claimed?
- Only the report text below — no validator has restated it as checkable claims yet.
- 2 · What does it affect?
- AreaOutside the audited area· Decided by agents · verified
- 3 · Is it reproducible?
- No validation has been run yet.
- 4 · What remains unclear?
- Not validated yet: no claims, no reproducer.
- 5 · What happens next?
- Decided by agents and verified by a second, independent agent — see the decision.
Original report
System details
Asus Zephyrus G14 + Dell U4025QW
What's wrong?
Description
The Omarchy network speed test works correctly while the laptop is connected
only through wifi.
When I connect the laptop to my Dell monitor (using Thunderbolt) and its integrated rj45 port
becomes active, the speed test reports 0 Mbps, even though the ethernet connection itself works normally.
Steps to reproduce
- Connect a laptop to wifi.
- Run the Omarchy network speed test.
- Confirm that it reports the expected download and upload speeds.
- Connect a monitor with an integrated rj45 adapter.
- Leave wifi enabled while ethernet becomes the preferred connection.
- Run the Omarchy network speed test again.
Actual result
The speed test reports 0 Mbps. or a value closed to 0.
Suspected cause
Currently, the script /usr/share/omarchy/bin/omarchy-network-speedtest uses ip route get 1.1.1.1, which checks the ipv4 route and may select wifi. However, because the subsequent curl requests are not bound to that interface, they may connect to fast.com over ipv6 and send the traffic through eth0 who has a lower metric. The script then measures the wifi interface instead of the interface carrying the traffic, resulting in a reported speed of 0 Mbps or closed to 0.
View raw text
### System details Asus Zephyrus G14 + Dell U4025QW ### What's wrong? ## Description The Omarchy network speed test works correctly while the laptop is connected only through wifi. When I connect the laptop to my Dell monitor (using Thunderbolt) and its integrated rj45 port becomes active, the speed test reports 0 Mbps, even though the ethernet connection itself works normally. ## Steps to reproduce 1. Connect a laptop to wifi. 2. Run the Omarchy network speed test. 3. Confirm that it reports the expected download and upload speeds. 4. Connect a monitor with an integrated rj45 adapter. 5. Leave wifi enabled while ethernet becomes the preferred connection. 6. Run the Omarchy network speed test again. ## Actual result The speed test reports **0 Mbps.** or a value closed to 0. ## Suspected cause Currently, the script `/usr/share/omarchy/bin/omarchy-network-speedtest` uses ip route get `1.1.1.1`, which checks the ipv4 route and may select wifi. However, because the subsequent curl requests are not bound to that interface, they may connect to fast.com over ipv6 and send the traffic through `eth0` who has a lower metric. The script then measures the wifi interface instead of the interface carrying the traffic, resulting in a reported speed of 0 Mbps or closed to 0.
Validation
Not checked yet. A validator will restate this report as checkable claims, map it to the project's requirements and write a reproducer that the proof engine runs.
Linked
Not linked to any known issue, other report or change yet.
Decision
Decisions are recorded by our staff — or, where this project allows it, by agents: checked by a second, independent agent, or by a single agent where the project's policy says so. Any decision reached so far is shown below.
- Out of scopeDecided by agents · verified · 2026-10-09 09:10 UTC