### Problem Description
On Intel-based Apple MacBooks (e.g. MacBookPro12,1 with Intel Iris Graphics 6100 / Broadwell-U), booting an encrypted Omarchy installation results in a completely blank, unlit internal screen immediately after entering the LUKS passphrase at boot.

The system finishes booting into the graphical desktop in the background, but the internal eDP panel remains asleep and unresponsive to TTY switching (`Ctrl+Alt+F3`).

### Root Cause & Evidence
1. **EFI Framebuffer to DRM Handover:** At boot, Apple EFI GOP initializes a basic framebuffer (`simpledrm`). Plymouth binds to this framebuffer to prompt for the LUKS passphrase.
2. **eDP Transceiver Sleep:** When `i915` is loaded late via udev after root decryption, unbinding `simpledrm` causes Apple's display multiplexer / eDP transceiver to enter a power-down/sleep state ($D3$). Because Apple firmware does not provide standard ACPI display re-initialization calls, `i915` fails to detect an active eDP hot-plug event and leaves the panel unlit.
3. **Debug Parameter Quirks:**
   - Standard debugging with `nomodeset` fails because Apple EFI disables the EFI framebuffer entirely when nomodeset is passed, leaving no console output.
   - Plugging in an external display (HDMI) forces an HPD (Hot-Plug Detect) interrupt, which wakes the GPU display engine and turns the internal eDP panel back on.
4. **Resolution:**
   - Adding `i915` to early initramfs (`MODULES+=(i915)`) allows DRM to take control before Plymouth starts, avoiding the disruptive late framebuffer handover.
   - Passing `video=eDP-1:e` forces the kernel to treat the internal eDP connector as enabled.

### Steps to Reproduce
1. Install Omarchy with LUKS full-disk encryption on an Intel MacBook (e.g., MacBookPro12,1 or MacBookPro11,x).
2. Boot without an external display connected.
3. Enter the LUKS passphrase at the prompt.
4. Decryption succeeds, but the internal screen blanks and stays completely dark.

### Verified Workaround
* Enable Early KMS for Intel in `/etc/mkinitcpio.conf.d/i915.conf`:
  ```bash
  MODULES+=(i915)
  ```
* Rebuild the initramfs / UKI (`limine-mkinitcpio` or `mkinitcpio -P`).
* Append `video=eDP-1:e` to `KERNEL_CMDLINE[default]` in `/etc/default/limine` and run `limine-enroll-config`.

### Suggested Improvement
In `install/hardware/apple/` (or `install/hardware/intel/`), mirror the behavior of `install/hardware/nvidia.sh` by automatically creating an early KMS drop-in (`/etc/mkinitcpio.conf.d/intel-kms.conf`) with `MODULES+=(i915)` when an Intel GPU is detected on Apple hardware.

### System & Hardware Information
```
┌──────────────────────Hardware──────────────────────┐
 PC: MacBook Pro (Retina, 13-inch, Early 2015) (1.0)
│ ├: Intel(R) Core(TM) i5-5257U (4) @ 3.10 GHz
│ ├: Iris Graphics 6100
│ ├󱄄: 2560x1600 @ 1.59x in 13", 60 Hz [Built-in]
│ ├󰋊: 36.10 GiB / 231.74 GiB (16%) - btrfs
│ ├: 4.10 GiB / 7.65 GiB (54%)
└ └󰓡 : 40.66 MiB / 15.30 GiB (0%)
└────────────────────────────────────────────────────┘

┌──────────────────────Software──────────────────────┐
 OS: Omarchy 4.0.4-1
│ ├󰔫: stable
│ ├: Linux 7.2.5-3-omarchy
│ ├: Hyprland 0.56.2 (Wayland)
│ ├󰏖: 10 (brew), 7 (flatpak), 999 (pacman)
│ ├󰸌: Aether
└────────────────────────────────────────────────────┘
```
* **Kernel:** `7.2.5-3-omarchy` (x86_64)
* **Bootloader:** Limine 12.8.0-1
* **PCI Device:** `00:02.0 VGA compatible controller: Intel Corporation Broadwell-U GT3 [Iris Graphics 6100] (rev 09) [8086:162b]`

> Filed by Gemini 3.8 Flash via Antigravity.