Proof Portal

Sign in
Project overview

Omarchy

ProbeLabs65 findings · 95 requirements

A proof layer — requirements, tests and verified fixes — for two of Omarchy's subsystems: the application menu (launcher scripts, QML model, JSONC config, search and selection) and the lock screen (lock scripts, QML, PAM authentication). Scope is deliberately limited to those components of omacom/omarchy; the rest of the distribution is not covered.

Inbox
ReportR-3451GitHub issuePublicReceived

GUI login became dependent on user shell working non-interactively

Reported by henderb · filed Oct 22, 2025Closed upstream on 2025-10-25 by ryanrhughes. GitHub close reason: completed. No closing PR or commit is recorded — "completed" alone is not evidence of a fix.

Open at source
Received and recorded verbatim. Nothing has been checked yet.

At a glance

1 · What is claimed?
Only the report text below — no validator has restated it as checkable claims yet.
2 · What does it affect?
Not yet mapped to any requirement or component.
3 · Is it reproducible?
No validation has been run yet.
4 · What remains unclear?
  • Not validated yet: no claims, no reproducer.
5 · What happens next?
Our staff decide whether the report is valid. Where this project allows it, agents decide whether it duplicates another report or a known issue. No decision has been recorded yet.

Original report

GUI login became dependent on user shell working non-interactivelyrevision 1 · captured 2026-10-04 11:42 UTC via poll

System details

Omarchy 3.x? -> 3.1.1

What's wrong?

After updating, I typed in my password and the screen went into powersave instead of opening the desktop.

hyprland would launch from one of the other terminals (CTRL+ALT+Fx) but launchers wouldn't work

restarting sddm seemed to work.

I eventually found that removing my call to keychain in my .bashrc let the system work again. I assume something was hanging on the password prompt for my ssh key, but it would be nice if the system was able to boot successfully as it did before the update.

I've switched from:

eval $(keychain -q --eval id_ed25519)

to:

if [[ $- == *i* ]]; then
	eval $(keychain -q --eval id_ed25519)
else
	eval $(keychain -q --noask --eval id_ed25519)
fi

I'm not sure what version I was on before. I got asked about a new default keychain (accepted), a nvim conf update (rejected), and the SUPER+SHIFT+B shortcut update were included.

View raw text
### System details

Omarchy 3.x? -> 3.1.1

### What's wrong?

After updating, I typed in my password and the screen went into powersave instead of opening the desktop.

hyprland would launch from one of the other terminals (CTRL+ALT+Fx) but launchers wouldn't work

restarting sddm seemed to work.

I eventually found that removing my call to keychain in my .bashrc let the system work again. I assume something was hanging on the password prompt for my ssh key, but it would be nice if the system was able to boot successfully as it did before the update.

I've switched from:

```
eval $(keychain -q --eval id_ed25519)
```

to:

```
if [[ $- == *i* ]]; then
	eval $(keychain -q --eval id_ed25519)
else
	eval $(keychain -q --noask --eval id_ed25519)
fi
```

I'm not sure what version I was on before. I got asked about a new default keychain (accepted), a nvim conf update (rejected), and the SUPER+SHIFT+B shortcut update were included.

Validation

Not checked yet. A validator will restate this report as checkable claims, map it to the project's requirements and write a reproducer that the proof engine runs.

Linked

Not linked to any known issue, other report or change yet.

Decision

Decisions are recorded by our staff — or, where this project allows it, by agents: checked by a second, independent agent, or by a single agent where the project's policy says so. Any decision reached so far is shown below.

No decision has been recorded yet.